28 March, 2024

Sourcing the correct metal hose

30 October, 2015

By Gary James Liptrot, managing director, TMS Group.


When looking to source metal hose for your application it is important to gather all the information you need to select the proper hose assembly for the application. The acronym S.T.A.M.P.E.D can serve as a handy aide memoire for the following guidance:

S.T.A.M.P.E.D

Size – What are the diameters of the hose required? Diameter of the end fittings?

Temperature – As temperature increases, pressure containing capabilities of the hose assembly decreases. The internal and external temperatures, minimum, maximum and operating all need to be taken in to consideration.

Application – How is the how going to be installed and what is its purpose? This includes the overall assembly length and what kind of movement is expected of the hose. Need this information to select proper length and flexibility of the hose assembly.

Media – Identify the all the fluids/chemicals that are exposed to the internal and external surfaces of the hose assembly. The purchaser must make certain that all components are compatible with media and the environment in which the hose is installed.

Pressure – Identify the maximum internal pressure that hose assembly must handle. Also, identify if the pressure cycles, surges or spikes. This information must be considered, since hose pressure ratings are reduced when these conditions are present.

Ends - Specify the end fittings required for installation. Materials and pressure ratings must meet the requirements of the application.

Dynamics – Identify the velocity of the fluid moving through the hose assembly. Since corrugated metal hose does not have a smooth interior, high velocities may cause resonant frequency vibration, causing early failure of the hose assembly.

Selection

Material – Utilise resources, such as National Association of Corrosion Engineers (NACE) and the Compass Corrosion Guides to make your material selection or call our customer service, for their assistance.

Pressure – You must make sure that the hose selected with have a maximum pressure rating that meets the requirements of your application. The stated maximum pressure rating is reduced based on each the following circumstances.

Temperature – As temperature increases, hose pressure capabilities decreases. Use the Temperature Derating Table to determine the factor to multiply the hose working pressure by to obtain the temperature derated working pressure.

Dynamic pressures – Pulsating, surge and shock pressures can damage a hose assembly. If the application has pulsating or surging pressure, the working pressure of the hose needs to be derated to ½ of its original value. If the hose is exposed to shock pressures, the working pressure must be derated to 1/6 of its original value.

Flexibility – Make certain that the minimum bend radius of the hose is less than the bend radius required by your application. See the vibration chart, to determine if the assembly will be exposed to normal vibration levels. If you have an application that involves excessive vibration, contact our customer service department for recommendations.

Fittings – End fittings are selected based on the mating fittings and the chemical compatibility with your application. You must also make certain that the end fitting pressure ratings, as well as those of the hose, exceed the required pressure rating of the application. Because applications vary widely, various end fittings can be welded together to make combinations to meet virtually any application needs. Contact us for these customer applications.

Length – How to select the proper length of a metal hose assembly:

• Properly design the application, do not pipe it first and buy a hose to fit.

• Never torque a hose or bend it in more than one plane.

• Never bend the hose tighter than its published bend radius.

• Never compress the hose from end to end.

• Install it correctly using the guidelines at: http://processhose.com/pdf/Hosemaster-Installation-metal-hose.pdf

• Use information at the following link to select the proper length: http://processhose.com/pdf/Hosemaster-metal-hose-length-considerations.pdf

As a Hose Master Factory Authorised Fabricating Distributor, TMS Group fabricates its flexible metal hose assemblies to the standards set forth by both NAHAD and the Hose Master Factory. All TMS’s fabricators have been fully trained, tested and approved to fabricate assemblies by the Hose Master factory.

www.flexiblemetallichoses.com




Events
 
Buyers' Guide Search
 
Search for UK supplier by name
Browse by Product Group.
Magazine
MARCH 2024To view a digital copy of the MARCH 2024 edition of Hydraulics & Pneumatics Magazine, click here.

For a FREE subscription please click here

To visit the Library for past issues click here

JANUARY/FEBRUARY 2024 IssueTo view a digital copy of the JANUARY/FEBRUARY 2024 edition of Hydraulics & Pneumatics Magazine, click here.

For a FREE subscription please click here

To visit the Library for past issues click here

JULY/AUG 2023 Issue inc. BUYERS' GUIDETo view a digital copy of the JULY/AUGUST ISSUE of Hydraulics & Pneumatics magazine that includes the ANNUAL BUYERS' Guide for 2023, click here.

To visit the Library for past issues click here

BFPA YearbookTo read the latest BFPA Yearbook, click here ..
BFPA Training AcademyClick the image to go to the BFPA Training Academy website
Compressed Air & Vacuum Technology Guide 2018To read the official BCAS Compressed Air & Vacuum Technology Guide 2018 click here
Offshore Europe Journal
Newsletter
 
Newsletter