9 August, 2022

Myths on Teflon hose (Dec 2011)

18 December, 2011

Three myths exist among hoses made with Teflon

Hoses made with a core of Teflon polytetrafluoroethylene (PTFE) have a richly deserved reputation for outstanding performance under severe application conditions. That’s why they are found in places like the space shuttle, aircraft landing gear and braking systems, and the self-contained breathing apparatus firefighters depend on to keep them safe.
But along with that reputation comes a pervasive belief that hoses made with Teflon carry a higher acquisition cost necessary only when no other material can meet the requirements. This brings us to the first of three myths about hoses made of Teflon.
High-Cost Solution
While it is true that the Teflon PTFE paste used to make high grade hose is a premium material, the hose itself is often a more economical choice than traditional products when total lifecycle-cost is considered. There are a number of factors to consider when comparing hose acquisition cost and performance.
First, in almost all cases a hose made with Teflon will outlast an ordinary rubber or thermoplastic hose under virtually any operating condition. Obviously, the advantage is greatest under the most severe conditions but it is almost always present, and usually significant. Whether this factor alone is enough to justify the higher initial acquisition cost of a hose made with Teflon will vary from application to application, but in most cases the answer is “no.”
That begins to change, however, when costs other than initial purchase price are considered: 
  • How much does the scheduled downtime for a hose change cost in terms of lost production, direct labor, hose and fitting inventories, and impact on other dependent processes?
  • How much does unscheduled downtime due to unpredictable hose failure cost?
  • How much does contamination caused by the buildup of materials on the I.D. of the hose cost annually?
  • How much does it cost to replace expensive boiler additives lost to effusion through rubber or thermoplastic steam hose cost?
A good example of the benefits of hoses made with Teflon can be found in the tyre industry.  The presses used in tire manufacturing use steam to cure the rubber, water to cool the die, and compressed air to blow the water out of the die prior to introducing steam for the next cycle.  A single hose is used to supply steam, water, and air to the press.
The OEM rubber hoses originally supplied with the presses had to be changed every two weeks on average to avoid in-process failures. Replacing them with hoses made with Teflon fluoropolymer and equipped with spring guards to minimize flexing fatigue has extended the hose-change interval to six months. The manufacturer reports that wear is not an issue at the six-month interval, but the hoses are replaced during scheduled press maintenance downtime as a pro-active measure.
Hoses made with Teflon can also reduce warranty costs for products like commercial/industrial coffee machines that tend to receive little or no maintenance from end users. They also add a factor of safety when used to drain hot products like fryer grease in fast food restaurants. Other advantages of hoses made with Teflon can have significant cost impacts in more specialized application areas. For example, carbon will not stick to the Teflon fluoropolymer core of hoses used as compressor discharge lines. That means the compressor damage caused by pieces of built-up carbon becoming detached from the discharge hose walls and circulating through the system is completely eliminated.
How much does it cost to replace an industrial compressor? There are also intangible benefits. Hoses made with Teflon generally have exposed stainless steel braids which lend a look of quality to the equipment to which they are attached. This cosmetic appeal “shows well” to potential customers and helps create a good first impression with potential customers. The bottom line here is simple. Hoses, like everything else, ought to be evaluated on their total lifecycle cost, not just their initial acquisition cost. Viewed in this way, hoses made with Teflon very often turn out to be the lowest-cost solution.
Kink & Crush
The truth is that all hoses tend to kink and crush easily, especially when they are improperly applied. Hoses made with Teflon are no better or worse than other materials when recommended bend radii and loadings are adhered to.
In applications where kinking or crushing is a possibility, it is a simple matter to add internal or external spring guards to reinforce the hose at critical points. Selecting a hose with thicker walls or a convoluted bore will also minimize kinking and resist crushing.
It is worthwhile to note that a hose made with Teflon having a convoluted bore has a recommended bend radius that is three to four times tighter than a PTFE hose of the same size with a smooth bore. Convoluted bores also exhibit greater crush resistance in vacuum applications.
The bottom line here is that hoses made with Teflon are no more prone to kinking or crushing than hoses made from other materials as long as they are applied according to the manufacturer’s recommendations. Where those recommendations must be exceeded, special accommodations such as additional guards or reinforcements are required, and that is true regardless of the material with which a hose is made.
All Hoses Made With Teflon, Are The Same
Teflon is the DuPont trademark   for its  family of fluoropolymer- materials, not all of which have the same properties. Two different Teflon fluoropolymers  are typically used in the hose industry, a melt-extrudable form (such as PFA, FEP, or ETFE) and a paste-extrudable form (PTFE). Melt-extrudable materials necessarily have a lower melting point than paste-extrudable materials. They also exhibit lower flex fatigue resistance. These lower physical properties are all reflected in the products using melt-extrudable Teflon fluoropolymers.
The premier PTFE resin used in hose construction is a grade of Teflon called T62 , the standard in Eaton’s PTFE hoses. Because Teflon T62 is not a thermoplastic, it cannot be continuously extruded, which has traditionally limited the length of hose that can be produced. This has been addressed by the latest generation of paste extrusion equipment, like that recently installed at Eaton’s Middlesex, N.C., plant that now has the capacity to produce long lengths of PTFE hose.  For a one –inch ID hose a 400 ft. continuous length is now possible.  This is a roughly 400 percent increase compared to older equipment that means fewer joints and less waste for end users.
There is a corollary to this myth that says all hoses with stainless steel braid are made with Teflon. This is definitely not the case. Braided stainless steel hoses are commonly used in cryogenic applications, and these hoses are not made with Teflon, but with a corrugated steel core.  A quick and easy way to tell is by looking for welded-on fittings, which are never used on hoses made with Teflon. Hoses made with Teflon are not the answer for every application, but they can deliver lower lifecycle costs than rubber or thermoplastic hoses in a much broader range of applications than the relatively restricted range for which they are commonly considered. If you have not looked at hoses made with Teflon because you thought they were too expensive, too prone to kinking and crushing, or didn’t have the right physical properties, it may be time to take a second look.

Buyers' Guide Search
Search for UK supplier by name
Browse by Product Group.
JUNE 2022 Issue To view a digital copy of the JUNE 2022 issue of Hydraulics & Pneumatics Magazine, click here.

APRIL/MAY 2022 IssueTo view a digital copy of the APRIL/MAY 2022 edition of Hydraulics & Pneumatics Magazine, click here.

For a FREE subscription please click here

July/August 2021 Annual Buyers' GuideTo view a digital copy of the JULY/AUGUST edition of Hydraulics & Pneumatics Magazine, click here.

For a FREE subscription please click here

BFPA YearbookTo read the latest BFPA Yearbook, click here
BFPA Training AcademyClick the image to go to the BFPA Training Academy website
Compressed Air & Vacuum Technology Guide 2018To read the official BCAS Compressed Air & Vacuum Technology Guide 2018 click here
Offshore Europe JournalOEE
Super Swivels
Impulse Automation Limited was established in 1960 and is based in the United Kingdom. We are an importer and distributor of mechatronic components used in a wide variety of industry sectors.Impulse Automation Limited
Hy-Pro FiltrationWEB LOCATOR