28 March, 2024

A material advantage for hydraulic piston rods

29 August, 2019

Mattias Awad, head of marketing and technology, OVAKO Cromax AB, offers a guide to material selection as hydraulic cylinders are required to deliver higher performance at lower cost.


The demand for increased operating pressures within a compact design is perhaps the single most important factor driving the uptake of new steel materials for hydraulic cylinders. For example, 180 bar was a typical requirement for construction machinery in the 1970s. Over time, this has increased to 210 bar and up to 280 bar. And in the near future we are looking at up to 35 MPa (350 bar).

Piston rod design

This doubling of operating pressure means that the hydraulic cylinder must now handle double the load. To achieve this, the main focus is on the chrome-plated and nickel-chrome-plated bars and tubes used primarily as piston rods, where the principal parameters (see Figure 1) are:

1) Dimensioning against fatigue, buckling and impact failure.

2) Tailoring the surface for low seal wear and limiting the risk of surface damage or corrosion.

Cromax steels

The main cost factor for the hydraulic rod is the bar diameter. Material, handling and cutting cost increase with the weight of the bar, while the cost of surface operations (machining, grinding, chrome plating etc.) increase with the surface area. As a result, the cost of a rod increases exponentially with the diameter. As a general rule of thumb, the cost of a piston rod decreases by 15 percent if the diameter is reduced by 5 mm. Other effects are lower weight, higher force in the minus direction and less fluctuation in the oil level in the tank, which could translate into lower energy consumption and possibilities for alternative designs.

Ovako has developed Cromax steels specifically as ‘piston-rod’ steels that offer the ideal combination of performance, surfaces and services to minimise the total cost of the piston rod (see Figure 2).

Slenderness ratio is crucial

Hydraulic piston rods must be dimensioned against buckling, fatigue and impact failure. The risk of buckling depends on the yield strength, the elastic modulus of the material and the geometry of the rod - defined as the slenderness ratio. Generally speaking, the buckling stress at small slenderness ratios corresponds to the yield stress of the material. It then decreases with an increasing slenderness ratio and eventually becomes independent of yield strength. In practice, 70 to 80% of all hydraulic cylinders are designed with low or moderate slenderness ratios (below 100). This means that yield stress has an important influence in defining the required diameter of the rod for cylinders operating in conditions where there is a risk of buckling.

Fatigue limit

In many applications, the piston rod operates in a dynamic environment with push-pull forces that make it susceptible to fatigue. Each rod has a unique fatigue limit and dimensioning is made on the basis of experience or through fatigue testing of finished piston rods or cylinders. As a general rule, fatigue strength increases with the tensile strength of the rod material. Guaranteed impact toughness might also be an additional considered for safety critical applications.




Events
 
Buyers' Guide Search
 
Search for UK supplier by name
Browse by Product Group.
Magazine
MARCH 2024To view a digital copy of the MARCH 2024 edition of Hydraulics & Pneumatics Magazine, click here.

For a FREE subscription please click here

To visit the Library for past issues click here

JANUARY/FEBRUARY 2024 IssueTo view a digital copy of the JANUARY/FEBRUARY 2024 edition of Hydraulics & Pneumatics Magazine, click here.

For a FREE subscription please click here

To visit the Library for past issues click here

JULY/AUG 2023 Issue inc. BUYERS' GUIDETo view a digital copy of the JULY/AUGUST ISSUE of Hydraulics & Pneumatics magazine that includes the ANNUAL BUYERS' Guide for 2023, click here.

To visit the Library for past issues click here

BFPA YearbookTo read the latest BFPA Yearbook, click here ..
BFPA Training AcademyClick the image to go to the BFPA Training Academy website
Compressed Air & Vacuum Technology Guide 2018To read the official BCAS Compressed Air & Vacuum Technology Guide 2018 click here
Offshore Europe Journal
Newsletter
 
Newsletter