25 September, 2017

Correct valve choice is a must (Dec 2013)

19 December, 2013

The right selection of the valves being used within any process control system is key to ensuring the performance and reliability of that system. Michael Hannig, product manager for Solenoid Valves at Bürkert Fluid Control Systems, looks at this process with particular focus on the chemical resistance of the various components. A valve in a brewery can be very different to one used in a pharmaceutical application for example; one of the critical aspects of valve design is the chemical resistance properties of the valve housing and the gasket materials in relation to the substances which it is expected to control. A long and trouble-free service can only be expected if the correct materials have been selected in the design process. In the case of a simple solenoid valve, many of the components, such as the plunger, return spring and seals are all exposed to the media. Therefore, information on the chemical compounds, temperature and pressure are all necessary to make an informed material selection. If the production process involves liquid food products, the plastics and elastomers used should also conform to the local food and hygiene regulations. In addition, some processes require a cleaning cycle to be performed in between production processes and so the data is also required for this procedure as well to ensure there is no undue material degradation. Factors such as mechanical loading, increased temperatures and chemical concentrations all have a bearing on the performance of individual components, which can be manufactured from a range of materials. In general the valve bodies are made from either brass or stainless steel with some being constructed from Polyamide. The type of valve most appropriate for each application is governed by a number of factors, but in general, plunger-type direct acting valves are best suited to neutral and clean fluids while pivoted armature valves offer improved reliability by employing a media separating membrane to control corrosive, contaminated or aggressive fluids. Extensive range The range of options for sealing and separating membranes is quite extensive with each having benefits and drawbacks. The combination of chemical compound, temperature, pressure and cost all have influence in this design decision. Below are some of the more common compounds in use with brief descriptions of their properties. PTFE (Polytetrafluoroethylene) is almost totally insoluble and chemically inert. It has a high temperature resistance and PTFE ball valve seats, because of their natural lubricity, require no lubrication. PTFE diaphragms and flange gaskets are used in the most severe chemical resistance applications. EPDM (Ethylene Propylene Terpolymer) is a synthetic rubber used as the standard seal material for many valves. It is the most economical choice of elastomer and has excellent chemical resistance to acids, alkalis, salts and many others at temperatures up to 90degC. However, it is not suitable for use with oils, petrochemicals and concentrated acids. NBR (Nitrile rubber) has a high chemical resistance to oil and petroleum but is weak on oxidising media such as acids. Nitrile also has excellent abrasion resistance and is less expensive than FKM and FFKM. FKM (Fluorinated elastomer) and perfluoro-elastomers (FFKM) are more expensive than neoprene and nitrile elastomers because they provide additional temperature and chemical resistance. Certain grades of FFKM can perform continuously at temperatures above 200degC. PPS (Polyphenyl sulphide) is a high performance thermoplastic used in many engineering applications. With the ability to perform above 200degC and with resistance to acids and alkalis as well as abrasion, PPS can be selected as a valve body material. PVDF (Polyvinylidene fluoride) is resistant to solvents, acids and bases, making it an ideal material for the valve body where high temperature resistance is not required. A very flexible product, it can be injected, moulded and welded, making for easier manufacturing of the valve bodies. PEEK (Polyether ether ketone) has excellent mechanical and chemical properties but is susceptible to high concentrations of sulphuric and nitric acid. This improved performance accounts for a higher price but provides superior qualities for valve bodies. To help designers and maintenance engineers through the selection process, Bürkert has released a chemical resistance chart and a selection guide for solenoid valves. The guides are available by visiting www.burkert.co.uk/ENG/literatur.php. www.burkert.co.uk Photo caption: Chemical resistance of valve materials twinpower valve showing seals.





Events
 
Buyers' Guide Search
 
Search for UK supplier by name
Browse by Product Group.
Magazine
Magazine To view a digital copy of the latest issue of Hydraulics & Pneumatics Magazine, click here.

For a FREE subscription please click here

Air-Tech Exhibition 2018
Previous IssueTo view a digital copy of the May/June issue of Hydraulics & Pneumatics Magazine, click here.

For a FREE subscription please click here

Fluid Power & Systems 2018
Buyers Guide - July/August Issue 2017To view a digital copy of the Buyers' Guide issue 2017 issue of Hydraulics & Pneumatics Magazine, click here.

July/August 2017 Annual Buyers Guide Issue
BFPA YearbookTo read the latest BFPA Yearbook, click here
BFPA Training AcademyClick the image to go to the BFPA Training Academy website
Compressed Air & Vacuum Technology Guide 2016To read the official BCAS Compressed Air & Vacuum Technology Guide 2016 click here
Smart Machines & FactoriesSmart Machines & Factories Magazine - the UK's first dedicated journal focusing on the fourth industrial revolution and transforming to a smart manufacturing era.
Newsletter
 
Newsletter