28 March, 2024

New valves can increase pneumatic system safety ratings to SIL1 and SIL2

09 December, 2016

Industries with highly automated processes, such as food & beverage and pharmaceuticals face many challenges, especially in terms of maintaining a safe environment. As increased legislation continues to require higher standards, Bürkert Fluid Control Systems has developed a series of innovative safety valve solutions that can be retro-fitted to existing control systems or incorporated into new designs.


Increasing levels of automation in industrial processes has brought with it higher levels of safety and reliability. This has led to, amongst other things, the adoption of the European Union’s Machinery Directive, 2006/42/EC and a number of other new standards such as IEC 62061. Within both of these pieces of legislation are details of increased safety functions, known as Safety Integrity Levels (SIL) or Performance Levels (PL) that categorise control components and structures with regard to fault detection, redundancy and reliability.

Essentially, plant manufacturers and operators are required to assess the safety of their equipment and if necessary make improvements to bring it within compliance. One of the crucial aspects of this evaluation is the provision of emergency valves and stop procedures that prevent harm in the event of an employee intervening in a process.

[head] Specific requirements

Safety circuits have very specific requirements, especially in terms of wiring and redundancy of components. As a simple example, an emergency stop circuit should have two sets of contacts in the pushbutton, which should be hard-wired to a safety relay or safety PLC which in turn is hard-wired to contacts that stop the process. This sort of arrangement would be classified as PLc or SIL1, which would be suitable for low level risks.

If the plant risk assessment has identified a higher category for a particular process, then it will be necessary to improve the reliability of the safety circuit. This can be done by introducing additional redundancy, which in the example above would be the addition of a control valve that could shutdown the process in question in the event that the original contacts had failed.

Many automated processes use pneumatic valve islands, connected to PLCs, to maintain the production process and any safety related circuits are separate from the valve island. In the wake of the introduction of EN ISO 13849, Bürkert has created two new valve types that could be retro-fitted onto the valve island and used for a safety-related shut-off, thanks to the additional wiring which allows the valve to be connected directly to a safety relay.

Meeting the requirements

This development enables plant managers to ensure their control structures meet the requirements for PLc or SIL1 with a compact solution and minimal changes to the circuit. The only addition to the control cabinet is the safety relay, if it was not already present, which keeps both costs and space to a minimum.

The second addition to the Bürkert range is the redundancy block Type MKRS, which can be installed in more demanding applications that require a higher level of safety. The introduction of a redundancy valve block will enable PLc or SIL2 to be achieved, which can apply to many applications in the hygienic sector where clean-in-place (CIP) procedures are used.

For example, in processes where an inspection hatch can be opened for maintenance, it is essential that the process must be stopped if a cover is removed at an inappropriate time. Under normal circumstances the safety valve on the pneumatic valve island will stop the process, but in situations where there is an increased risk the redundancy block is positioned so that if the safety valve does not operate, then the process will be stopped by the Type MKRS valve.

Equally of use to process engineers designing new systems, this is a very compact solution that can also easily be integrated into an existing control system without affecting the process control programming. For designers and OEMs these new innovations from Bürkert offer excellent reliability and minimal impact on current designs while delivering increased safety levels without increasing the footprint of the control structure.

www.burkert.co.uk




Events
 
Buyers' Guide Search
 
Search for UK supplier by name
Browse by Product Group.
Magazine
MARCH 2024To view a digital copy of the MARCH 2024 edition of Hydraulics & Pneumatics Magazine, click here.

For a FREE subscription please click here

To visit the Library for past issues click here

JANUARY/FEBRUARY 2024 IssueTo view a digital copy of the JANUARY/FEBRUARY 2024 edition of Hydraulics & Pneumatics Magazine, click here.

For a FREE subscription please click here

To visit the Library for past issues click here

JULY/AUG 2023 Issue inc. BUYERS' GUIDETo view a digital copy of the JULY/AUGUST ISSUE of Hydraulics & Pneumatics magazine that includes the ANNUAL BUYERS' Guide for 2023, click here.

To visit the Library for past issues click here

BFPA YearbookTo read the latest BFPA Yearbook, click here ..
BFPA Training AcademyClick the image to go to the BFPA Training Academy website
Compressed Air & Vacuum Technology Guide 2018To read the official BCAS Compressed Air & Vacuum Technology Guide 2018 click here
Offshore Europe Journal
Newsletter
 
Newsletter